13313028229
产品中心
联系我们
名称：保定市隔离墩模具厂
微信：xxx
手机：13313028229
联系人：xxx
地址：xxx
新闻动态
滚塑成型的生产过程
滚塑成型的生产过程
Production process of roll forming
在进行滚塑制作工艺之前，你需要准备好一些质量良好的模子，并将其放置在一台塑造机器上，这台铸造机器内还分别设有制热和制冷的两个装置。在安置妥当之后，首先把几块模具放在机器上面。然后，在每个模具内放入早期规则型塑料树脂，再将模具从垂直和水平的两个角度慢慢地旋转放至烤箱中。融化了的树脂将炙热的模具和外层包装均匀紧密地粘合在一起。随后，再将模具放入制冷循环设备中，令模具在其中继续旋转直至其每一部分的厚度均保持一致。当模具被冷冻完毕之后，将其从机器上取下来。在整个制作过程中，模具转动的速度，加热和冷却的时间统统要经过严格的精确控制。
Before the roll molding process, you need to prepare some good molds and place them on a molding machine, which is equipped with two devices of heating and cooling. After setting it up, first put some molds on the machine. Then, place the early regular plastic resin in each mold and slowly rotate the mold from both vertical and horizontal angles into the oven. The melted resin will bond the hot mold and the outer packaging evenly and tightly. Then, put the mold into the refrigeration cycle equipment, so that the mold continues to rotate in it until the thickness of each part is consistent. When the mold is frozen, remove it from the machine. In the whole manufacturing process, the speed of mold rotation, heating and cooling time are all strictly and accurately controlled.
Production process of roll forming
在进行滚塑制作工艺之前，你需要准备好一些质量良好的模子，并将其放置在一台塑造机器上，这台铸造机器内还分别设有制热和制冷的两个装置。在安置妥当之后，首先把几块模具放在机器上面。然后，在每个模具内放入早期规则型塑料树脂，再将模具从垂直和水平的两个角度慢慢地旋转放至烤箱中。融化了的树脂将炙热的模具和外层包装均匀紧密地粘合在一起。随后，再将模具放入制冷循环设备中，令模具在其中继续旋转直至其每一部分的厚度均保持一致。当模具被冷冻完毕之后，将其从机器上取下来。在整个制作过程中，模具转动的速度，加热和冷却的时间统统要经过严格的精确控制。
Before the roll molding process, you need to prepare some good molds and place them on a molding machine, which is equipped with two devices of heating and cooling. After setting it up, first put some molds on the machine. Then, place the early regular plastic resin in each mold and slowly rotate the mold from both vertical and horizontal angles into the oven. The melted resin will bond the hot mold and the outer packaging evenly and tightly. Then, put the mold into the refrigeration cycle equipment, so that the mold continues to rotate in it until the thickness of each part is consistent. When the mold is frozen, remove it from the machine. In the whole manufacturing process, the speed of mold rotation, heating and cooling time are all strictly and accurately controlled.
